Plumbing 101: A Guide to Bathtub Installation

Book Inspection

Are you trying to find content around How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?

Mounting a bathtub isn't exactly brain surgery, yet it does call for strong plumbing, carpentry, and also often, tiling abilities. Changing an old tub with a new one is also a reasonably tough job. If the old bathtub is easily obtainable, the job can relocate rapidly; if you need to open up a wall surface to remove the old bathtub and also place the new tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly need a helper to move out the old tub and also embeded in the new one. Make sure you have certified yourself for the work and also are comfortable trying it. Instead of employing a professional to take control of a halfway-completed job, it is far better to consider employing one before you start. Chances are you might need a specialist plumber to make tube connections.
This post will help you set up a brand-new tub in your shower room if you have currently bought a new tub and do not need to transform the arrangement of your previous water supply pipelines.
Your devices and product checklist need to make up the following:

New Bathtub

Hammer

Pipeline Wrenches

Prybar

Safety Glasses

Level

Pliers

Adjustable Wrench

Putty Blade

Screwdriver

Cold Blade

Tape Measure

Pipeline Caps

Preparing for the Installment

To start with, the supporting structure supplied with the bath must be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is important to make sure that if the tap comes with a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to prevent stress on the bath tub.
Fit the flexible faucet adapters to the bottom of the two faucets making use of 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you use every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to currently prepare to be suited its final position.

Removing Old Taps

If you require to replace old taps with new ones as a part of your installation, after that the first thing you ought to do is separate the supply of water. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The procedure of getting rid of the existing taps can be fairly problematic due to the limited gain access to that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth ready for the remaining water that will come from the pipelines. Once the supply pipelines have actually been gotten rid of, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from turning throughout this process. Once the taps have been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing substance.
Prior to moving on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.

Installing the Bathtub

Using both wooden boards under its feet, place the bathtub in the called for position. The wood boards are handy in uniformly spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto 4 small factors.
The following objective is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level and adjusting the feet on the tub till the level reads level.
To mount taps, fit all-time low of the furthest versatile faucet connector to the suitable supply pipeline by making a compression join; after that do the very same for the other tap.
Switch on the water system and also inspect all joints and also new pipework for leaks as well as tighten them if necessary. Fill up the bath tub as well as also inspect the overflow outlet and the typical outlet for leakages.
Finally, repair the bath paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the tub ought to wait till the tub has actually been used a minimum of once as this will settle it into its last placement.

Suitable New Taps

If the tails of the new faucets are plastic, after that you will require a plastic connector to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, then you will require minimizing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the installing hole in the bath/basin making certain that the washers are in area in between the faucet and also the sink. Safeguard the tap in position with the producer supplied backnut. As soon as the faucet is firmly in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous type must be linked to the faucet ends first, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.

Tiling Around the Tub

In the location where the bathroom fulfills the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to break an inflexible seal, triggering the water to pass through the wall surface between the bath and also the tiling, leading to problems with wetness and also feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your fixtures and also installations. They are offered in tubes and cartridges, and also can securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the tub with water before sealing, to enable the motion experienced when the bathtub is in use. The sealer can fracture rather early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise easily readily available on the marketplace. It is advisable to fit the floor tiles using waterproof or water-proof sticky as well as grout.

A Step-by-Step Guide to Installing a Bathtub

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

Remove the Existing Bathtub

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

Choose the Right Bathtub

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

Install the Plumbing and Ledger Board

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

Install the Bathtub

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

Hook up the Plumbing

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

Install the Bathtub Surround

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

We had been shown that article about Installing A Bathtub from a good friend on our other website. Appreciated our posting? Please share it. Help other people discover it. Thank you for taking the time to read it.

Trusted help? Ring now.