Understanding Plumber's Essentials for Bathtub Installation
EstimateAre you on the lookout for content around How to Install a Bathtub Yourself?
Installing a bathtub isn't exactly brain surgery, but it does require solid plumbing, carpentry, and also occasionally, tiling abilities. Changing an old tub with a brand-new one is also a moderately challenging task. If the old bathtub is easily available, the job can move immediately; if you have to open a wall surface to get rid of the old tub and place the brand-new bathtub, the task is much harder. In either situation, the job is within a home handyman's skills, although you will require a helper to vacate the old tub as well as embeded in the brand-new one. Make sure you have actually certified on your own for the work and are comfortable attempting it. As opposed to hiring a service provider to take over a halfway-completed job, it is much better to take into consideration using one before you begin. Opportunities are you may need a specialist plumber to make tube links.
This short article will aid you mount a brand-new bathtub in your shower room if you have already acquired a brand-new bathtub as well as do not need to change the setup of your previous water system pipes.
Your tools and material checklist should comprise the following:
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installation, then the first thing you must do is separate the water system. After doing so, switch on the faucets to drain pipes any kind of water staying in the system. The process of eliminating the existing faucets can be quite troublesome because of the limited gain access to that is often the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the taps. Have a fabric all set for the continuing to be water that will certainly originate from the pipes. As soon as the supply pipelines have actually been removed, use the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from transforming during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing compound.
Prior to proceeding to fit the new taps, contrast the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and the various other end provides a link to the existent supply pipes.
If you need to fit a monobloc, then you will need lowering couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin guaranteeing that the washers remain in location in between the faucet as well as the sink. Safeguard the tap in place with the supplier given backnut. When the faucet is firmly in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The previous kind should be linked to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Mounting the Tub
Making use of both wood boards under its feet, position the bathtub in the needed position. The wood boards are valuable in evenly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 small factors.
The following objective is to guarantee that the tub is leveled all round. This can be attained by examining the spirit level as well as readjusting the feet on the bathtub till the level reviews level.
To install taps, fit the bottom of the furthest adaptable tap connector to the suitable supply pipeline by making a compression sign up with; after that do the very same for the various other tap.
Activate the water supply and examine all joints as well as brand-new pipework for leaks and also tighten them if required. Load the bathtub as well as also examine the overflow outlet and the typical outlet for leaks.
Finally, deal with the bath paneling as explained in the manufacturer's user's manual. Tiling and securing around the bath tub needs to wait up until the bathtub has been utilized at the very least when as this will certainly settle it into its final placement.
Preparing for the Setup
Firstly, the supporting structure supplied with the bathroom ought to be fitted (if called for) according to the maker's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is very important to see to it that if the faucet includes a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps unit to stop stress on the bath tub.
Fit the versatile faucet connectors to the bottom of the two taps using 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you utilize all of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom must currently be ready to be suited its last position.
Tiling Around the Bathtub
In the location where the bath satisfies the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to break an inflexible seal, triggering the water to permeate the wall in between the bathroom as well as the tiling, resulting in problems with moisture and also feasible leaks to the ceiling below.
You can select from a range of coloured sealers to blend in your components and also fittings. They are marketed in tubes as well as cartridges, and are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly load the bathtub with water prior to securing, to enable the movement experienced when the tub remains in usage. The sealant can crack fairly early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also quickly readily available on the marketplace. It is recommended to fit the floor tiles making use of waterproof or water resistant glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am very excited about How to Install a Bathtub and I am assuming you enjoyed the entire article. In case you liked our article kindly do not forget to pass it around. We truly appreciate reading our article about How to Install a Bathtub Yourself.
Instant help? Contact.